Solar Street Light Price: What Decides the Cost of an AI IoT System

Section 1. The short answer: quoted per project, no fixed price There is no fixed price list for a Werise solar street light, and this guide does not invent one. Every system is quoted per project, because the price depends on the full configuration — lamp, panel, battery, controller, pole height, quantity and customisation — not on wattage alone. A buyer who asks only “how much is a 100W solar street light” will get a useless answer, from any supplier, because two 100W lights can be entirely different systems. The rest of this guide explains what goes into the quote, so the reader can ask for the right one. Section 2. The seven cost drivers 1. Wattage and lumens. Lumens are the light output; efficacy (lm/W) is lumens per watt. Cost follows the light output the project needs, not the wattage label. Two verified examples: HC-WT2-A50W is 50W at 180–210 lm/W, maximum 9,000–10,500 lm; HC-CZSL-39 is 150W, 27,000–30,000 lm. A higher-wattage light with low efficacy can cost more and light less than a lower-wattage light with high efficacy. 2. Panel and battery. The energy system is usually the largest cost block after the lamp itself. The panel must recharge the battery in local daylight; the battery must carry the light through the night and through cloudy days, in dimmed mode. Verified matched pairs from Werise product pages: HC-WT2-A50W, 20W 18V panel + 15Ah 3.2V LiFePO4; HC-CZSL-39-100W, 60W 18V panel + 60Ah 3.2V LiFePO4; HC-CZSL-39-150W, 70W 18V panel + 75Ah 3.2V LiFePO4. A bigger panel and battery cost more — and a system quoted with an undersized pair will cost more later, in failed nights. 3. Controller. The AI IoT MPPT controller (PC & App, light & remote control) is stated on the product pages of HC-CZSL-39, HC-CZSL-39-100W, HC-JDSL-02 and HC-WT2-A50W. It adds remote monitoring, batch on/off, dimming and colour-temperature control, GPS positioning and anti-theft on the models whose pages state those functions. Some Werise floodlights use Tuya control instead, over a 4G built-in chip (factory-confirmed 2026-11-14). Controller choice is a cost driver — do not compare an AI IoT quote with a basic-controller quote as if they were the same product. 4. Split vs all-in-one. In a split system the head, panel and battery box are separate components, and each can be sized and customised per project — HC-JDSL-02 is a split system with configurable power models (400–800W), panel 100–200W 18V and battery options of 3.2V, 6.4V, 12.8V or 25.6V LiFePO4. A split system costs more to configure and install than a fixed all-in-one, and it fits projects a fixed unit cannot. Do not price a split system against an all-in-one on wattage alone. 5. Pole height and mounting. Mounting heights from Werise product pages: HC-JDSL-02 at 8–13 m by power model; HC-CZSL-39-100W at 4–6 m; HC-CZSL-39-150W at 6–8 m; the two verified project cases use 12 m poles. Taller poles, dual-head configurations and wall-versus-pole mounting change the hardware and the installation — all of it belongs in the quote, not in the lamp price. 6. Quantity and customisation. There is no MOQ — even a single unit can be customized — and lead time is 10–30 days (factory-confirmed 2026-11-14). Quantity, custom battery or pole configurations and custom optics all move the unit price, so ask for a quantity-based quote for the exact configuration rather than comparing a single-unit price with a bulk price. 7. Shipping, installation and after-sales. Warranty is 3 years for the whole unit and 5 years for core components. Every light undergoes aging testing before shipment (HC-JDSL-02 product page). Shipping, installation and after-sales support are project costs — confirm what is included in the quote before ordering; this guide does not state freight or installation figures. Section 3. Why wattage alone cannot price a light Two verified Werise cases make the point. In Guangxi, HC-JDSL-02 heads are rated 200W per head but the case page records actual operating power of 60W per head. At Shenzhen Airport, HC-WT3-A200W heads are rated 200W with a configured operating power of 50W. The same “200W” label covers different energy systems, different battery banks and different operating schedules — so a price quoted on wattage alone is not a comparable price. Ask for the full spec: lamp power and lumens, panel, battery, controller, pole height, dimming schedule and warranty. Section 4. Worked comparison — verified specs, no prices Model Lamp power Lumens (max, where stated) Solar panel Battery Controller Mounting height Warranty HC-WT2-A50W 50W 9,000–10,500 lm 20W 18V mono 15Ah 3.2V LiFePO4 AI IoT MPPT (PC & App) Confirm before ordering 3 years HC-CZSL-39-100W 100W 18,000–21,000 lm 60W 18V mono 60Ah 3.2V LiFePO4 AI IoT MPPT (PC & App) 4–6 m 3 years HC-CZSL-39 (150W) 150W 27,000–30,000 lm 70W 18V mono 75Ah 3.2V LiFePO4 AI IoT MPPT (PC & App) 6–8 m 3–5 years (by configuration) HC-JDSL-02 400–800W (configurable) Confirm before ordering 100–200W 18V (configurable) 3.2V / 6.4V / 12.8V / 25.6V LiFePO4 (configurable) AI IoT MPPT (PC & App) 8–13 m (by power model) 3–5 years (by configuration) Note: the HC-CZSL-39-100W lumen total is stated on its product page (18,000–21,000 lm). HC-WT2-A50W mounting height is not stated on its product page. Section 5. What a like-for-like quote needs The HC-CZSL-39-150W product-page FAQ states what Werise asks for: the project country/city, road or site dimensions, pole height and spacing, required operating hours, quantity and any special requirements. Send all of it. A quote built on wattage alone is not like-for-like with a quote built on the full spec, and the cheaper of the two is usually the one with the smaller panel, the smaller battery or the shorter warranty — the parts that fail first. Also state the operating pattern: Werise solar lights run 10–12 hours per night in time-segmented dimming mode, not at 100% brightness all night, with up to 3 rainy days of backup in dimmed mode (factory-confirmed 2026-11-14). A quote that assumes full power all night is pricing a different system. Section 6. How to compare two quotes Same panel wattage and battery capacity, or the comparison is void. Same controller — AI IoT MPPT with PC/App remote management is not the same product as a basic controller, and Tuya (4G built-in chip) is a third path. Same warranty: 3 years whole unit / 5 years core components, and check whether the quoted warranty is shorter. Same scope: does the price include poles, foundations, shipping and installation, or the lights only? Confirm before ordering. Same dimming schedule: 10–12 hours dimmed, up to 3 rainy days backup — or a different schedule with a different battery. Ask for the model number and the datasheet, not a wattage label. Two “100W solar street lights” can differ in every line of the table in section 4. Section 7. FAQ Q: How much does a solar street light cost? A: Werise quotes per project — there is no fixed price list. Send the project country/city, road dimensions, pole height and spacing, required operating hours, quantity and any special requirements, and Werise will quote the exact configuration. Q: Why do two 100W solar street lights cost different amounts? A: Because watts are only the lamp rating. Panel size, battery capacity, controller, LED efficacy, pole height and warranty all differ between two “100W” lights — and those are what the price is mostly made of. Q: Does a higher price mean a better light? A: Not necessarily. Compare the full spec — lumens, panel, battery, controller, mounting height and warranty — not the wattage label and not the price alone. Q: Is there a minimum order quantity? A: No. There is no MOQ — even a single unit can be customized — and lead time is 10–30 days (factory-confirmed 2026-11-14). Ask for a quantity-based quote for the exact configuration. Q: What information do I need to send for a quote? A: Project country/city, road or site dimensions, pole height and spacing, required operating hours, quantity and any special requirements. If full technical data is not available, drawings, site photos or basic project information are enough to start. Send your road width, pole height and hours per night — we will recommend the model and a lighting layout.

Solar Street Light Installation: A Practical Guide for AI IoT Projects

Section 1. What installation involves — and what it does not A solar street light is an off-grid system: light head, solar panel, battery box, controller and pole. There is no power cable to run to the grid — the Shenzhen Airport case states the project required “solar-powered parking lot lighting without a grid power connection”. There is still a foundation to build for each pole, and the foundation specification depends on pole height and local conditions — confirm before ordering. The AI IoT part is the controller and the platform. The models used in this guide carry an AI IoT MPPT controller (PC & App, light & remote control), and the installation is not finished until the light is visible and controllable on that platform — not when the pole is up. Section 2. Before anything is installed: the site survey The survey decides the configuration. The HC-CZSL-39-150W product page FAQ puts it plainly: Werise normally evaluates the project location, road width, pole height, pole spacing, daily operating hours, required illumination level and local solar conditions, then recommends wattage, optics, solar panel and battery configuration. Send those inputs before the configuration is fixed — not after the poles are ordered. Three survey items buyers most often skip: Shading on the panel — the panel must stay uncovered and unshaded. A cover on the panel greatly reduces charging efficiency (stated on the HC-CZSL-39 product pages). Check trees, buildings and the pole’s own head for shading before fixing panel positions. Hours per night and rainy-day backup — Werise solar lights run 10–12 hours per night in time-segmented dimming mode, not at 100% brightness all night, with up to 3 rainy days of backup in dimmed mode (factory-confirmed 2026-11-14). Settle the hours and the backup days in the survey, because they decide the panel and battery size. What to send Werise — country/city, road or site dimensions, pole height and spacing, required operating hours, quantity and any special requirements (HC-CZSL-39 product-page FAQ). Drawings, site photos or basic project information work if full technical data is not available yet. Section 3. Poles and mounting heights Mounting height is set per project, from the model’s own range: HC-CZSL-39 150W: 6–8 m mounting height (product page). HC-JDSL-02: 8–13 m mounting height by power model (product page spec table: 400W 8–9 m, 500W 9–10 m, 600W 10–11 m, 700W 11–12 m, 800W 12–13 m). HC-CZSL-39-100W: 4–6 m mounting height, pole or wall mounting. Project poles run taller: both verified cases in this guide use 12 m poles — Guangxi industrial access road and Shenzhen Airport parking lot. Do NOT publish a generic pole-height-to-road-width rule, and do not copy a spacing figure from one model to another. The HC-ZY-01 product page shows a 6 m mounting height with 12 m pole spacing only as a reference configuration for that tested luminaire — it is not a general rule, and this guide does not repeat it as one. Spacing is set by a lighting calculation for the project. Section 4. Panels and battery boxes (split systems) In a split system the head, the panel and the battery box are separate components, so each is mounted and checked on its own. Panel and battery are matched per model — the pairs below are from each model’s own product page: HC-WT2-A50W: 20W 18V mono panel + 15Ah 3.2V LiFePO4 external battery box. HC-CZSL-39-100W: 60W 18V mono panel + 60Ah 3.2V LiFePO4 external battery box. HC-CZSL-39-150W: 70W 18V mono panel + 75Ah 3.2V LiFePO4 external battery box. HC-JDSL-02: configurable — panel 100–200W 18V; battery 3.2V, 6.4V, 12.8V or 25.6V LiFePO4, capacity matched to lighting power, operating hours and local sunlight. The battery box is external on these models. Check its mounting and that it is protected from damage on site. All four models above are IP65 on their product pages. Do not swap a panel or battery between models — the pair is part of the configuration. Section 5. Controller and app setup The AI IoT MPPT controller (PC & App, light & remote control) is stated on the product pages of HC-CZSL-39, HC-CZSL-39-100W, HC-JDSL-02 and HC-WT2-A50W. Setup covers on/off, the time-segmented dimming schedule (10–12 hours per night, dimmed — factory-confirmed) and colour temperature, which is AI-adjustable per model: 3000K–6000K on HC-JDSL-02, HC-CZSL-39-100W and HC-WT2-A50W; 2300K–6000K on HC-CZSL-39-150W. Two limits to keep straight: Tuya models are a different control path: Tuya connects over a 4G built-in chip (factory-confirmed 2026-11-14). Do not describe a Tuya model as AI IoT, or an AI IoT model as Tuya. Sensors are customised per project. There are no fixed detection distance, angle or delay figures — if the project needs sensors, confirm the configuration before ordering. Section 6. Commissioning and the remote-monitoring check Every light undergoes aging testing before shipment (HC-JDSL-02 product page). On site, commissioning is a platform check, not just a look at the pole. The definition post states the AI management system can monitor battery status, power generation and LED working status — so check all three for every light, plus: batch on/off, dimming and colour-temperature adjustment work from the PC/App platform; GPS position is recorded and the anti-theft function is active — GPS positioning and anti-theft are stated on the product pages of HC-CZSL-39, HC-JDSL-02 and HC-WT2-A50W. Do not claim GPS for a model whose page does not state it; the dimming schedule is running as configured, not at full power all night. Handover checklist: each light visible on the platform; battery, generation and LED status reporting; dimming schedule running; GPS position recorded; remote on/off and dimming tested. Accept handover only when the checklist passes for every light, not for a sample. Section 7. Two real installations Guangxi — industrial access road (HC-JDSL-02 Custom AI IoT Split). 12 m poles; two 200W LED heads per pole; two 160W monocrystalline panels and two 6.4V 100Ah batteries per pole; AI IoT MPPT controller. The case page records actual operating power of 60W per head against the 200W rating, and luminous efficacy of 198 lm/W. The lesson for buyers: rated watts and operating watts are different numbers, and the panel and battery per pole are part of the answer. Shenzhen Airport — parking lot, 20,000 m² (HC-WT3-A200W). October 2026 project. 200W rated per head, 50W configured operating power; 6 × 100W monocrystalline panels per pole; 12 × 6.4V 60Ah battery packs per pole; 12 m poles. The case page notes the project required attention to glare and to electromagnetic compatibility for lighting and control equipment used near airport facilities. The lesson: a large site means a large battery bank per pole, and airport-adjacent projects carry checks — glare, interference — that a standard road project does not. Section 8. What the factory supplies vs what the project provides Confirm in the quote what is included: lights, panels, battery boxes and controller are the system. Poles, foundations and on-site labour are project items — confirm before ordering; this guide does not claim Werise supplies poles. Two commercial facts that affect planning: there is no MOQ — even a single unit can be customized — and lead time is 10–30 days (factory-confirmed 2026-11-14). Confirm the lead time for the exact configuration before ordering, because a custom battery or pole configuration is not a stock item. Section 9. FAQ Q: How long does a solar street light installation take? A: There is no fixed figure — it depends on the number of lights, pole height, site access and weather. Confirm the schedule per project before ordering. Q: Does a solar street light need a grid connection or wiring? A: No grid connection — the Shenzhen Airport case is solar-powered parking-lot lighting without a grid power connection. Remote monitoring runs through the cloud platform, so confirm the network path for the site before ordering. Q: What should I check before accepting handover? A: The checklist in section 6: each light visible on the platform; battery, generation and LED status reporting; dimming schedule running; GPS position recorded; remote on/off and dimming tested. Q: Can the lights go on existing poles? A: Mounting is per model — HC-CZSL-39-100W lists pole or wall mounting. Confirm the mounting method and the condition of existing poles for the exact model before ordering. Q: What if a light stops working after installation? A: Check the platform first — battery status, power generation and LED working status will usually show whether it is a battery, charging or LED problem. Warranty is 3 years for the whole unit and 5 years for core components. Then contact Werise with the light’s model and its platform status. Send your road width, pole height and hours per night — we will recommend the model and a lighting layout.

How to Choose Solar Street Light Wattage: 50W vs 150W vs 200W

Section 1 — Wattage is only one part of the system A solar street light’s wattage is the lamp’s rated power. It does not, on its own, tell a buyer how bright a road will be or how long the light will stay on. The same wattage can give very different results depending on the solar panel, the battery, the controller, the mounting height and the dimming schedule. Buyers who choose by wattage alone are the buyers who end up with a dark road or a light that dies before morning. That is why this guide works through the whole system, then uses Werise models as worked examples — each figure below is taken from that model’s own product page, not from a generic wattage table. Section 2 — The four numbers to check before the wattage Lumens and efficacy (lm/W). Lumens are the light output; efficacy is lumens per watt. Two 100W lights can differ by thousands of lumens. Panel and battery. The panel must recharge the battery in local daylight; the battery must carry the light through the night and through cloudy days, in dimmed mode. Mounting height and spacing. A higher pole spreads the same light over a wider area at lower brightness. Height and spacing decide whether there are dark gaps between poles. Dimming schedule. Werise solar lights run 10–12 hours per night in time-segmented dimming mode, not at 100% brightness all night (factory-confirmed 2026-11-14). A wattage quoted without a dimming schedule is not a runtime promise. Section 3 — Worked examples — Werise models only 50W — HC-WT2-A50W (garden / small-area example). 50W, 180–210 lm/W, maximum 9,000–10,500 lm at full power. Brightness is multi-mode and adjustable to customer requirements — 1,000 / 1,600 / 1,900 lm are example dimmed settings, not a fixed three-level limit — and actual brightness varies with battery charge. Use it to show how a small-wattage light can still be the right answer when the area is small and the dimming schedule is right — and the wrong answer for a wide road. 150W — HC-CZSL-39 (road example). 150W, 27,000–30,000 lm, CREE 3030 LEDs, IP65, 6–8 m mounting height. Product page describes it for roads, parks, rural communities, public areas and remote projects. This is the guide’s main road example: same logic as the 50W case, scaled up — more lumens, higher pole, wider coverage. 200W — HC-WT3-A200W (project example, Shenzhen Airport parking lot). 200W rated per head, configured operating power 50W, 6 × 100W solar panels per pole, 12 m poles, October 2026 project. Use it to make the guide’s central point concrete: rated watts and operating watts are not the same number, and the panel array and pole height are part of the answer. Section 4 — 50W vs 150W vs 200W — how to decide The decision guide is the three worked examples above, plus this checklist: Road width and pole height available → which mounting-height band (e.g. 6–8 m for HC-CZSL-39) fits? Hours per night and cloudy-day backup needed → does the model’s dimmed-mode schedule cover it? (Werise: 10–12 h dimmed, up to 3 rainy days — confirm per model before ordering.) What must stay bright all night, and what can dim when the road is empty? → multi-mode brightness, configured per project. Is remote monitoring / dimming needed? → AI IoT models only; do not attribute AI IoT to a model whose page does not state it. For a broader selection framework, see the municipal and rural road solar street light guide. FAQ Q: How many watts do I need for a solar street light?A: It depends on road width, pole height, required brightness and how many hours the light must run. Wattage alone is not enough — check lumens, panel and battery, mounting height and the dimming schedule. Send your road width and pole height and Werise will recommend a model. Q: Is a higher-wattage solar street light always brighter?A: Not necessarily. Brightness is lumens, and lumens = watts × efficacy (lm/W). A 50W light at 180–210 lm/W (HC-WT2-A50W, maximum 9,000–10,500 lm) can out-perform a higher-wattage light with lower efficacy. Check the model’s own figures. Q: How long will a solar street light stay on each night?A: Werise solar lights run 10–12 hours per night in time-segmented dimming mode, not at 100% brightness all night, with up to 3 rainy days of backup in dimmed mode. The exact schedule is configured per project — confirm for the exact model before ordering. Send your road width, pole height and hours per night — we will recommend the model and a lighting layout.

Werise AI IoT solar street light projects on municipal and rural roads in nine countries

Municipal and Rural Road Solar Street Lights: How to Choose

Choosing a solar street light starts with the road, not the product. A municipal road and a rural village road need different mounting heights, different coverage, and different maintenance plans — even when the lights look similar.

GPS Tracking for Stolen Solar Road Light Recovery

Solar Street Lights with GPS Tracking and AI IoT Control for Remote Projects

GPS tracking helps locate solar street lights, flag unusual movement, and support theft investigations and asset recovery.

Уличный солнечный фонарь AI LOT

Inside Smart Street Lights: AI IoT Sensors, Controllers, Cameras and Cloud Platforms Explained

Узнайте, как датчики, контроллеры, камеры и облачные платформы вписываются в архитектуру солнечного уличного освещения на основе ИИ и IoT, с помощью контрольного списка для проверки, специфичного для каждой модели.

Продукты
Контакты
WhatsApp
Электронная почта